InterceptRadio.com Forums

The radio website that puts military & officer safety ahead of profits.
It is currently Fri Jun 27, 2025 1:17 am

All times are UTC - 8 hours


Forums       Map Search       Database Search       Live Audio       Alerts       Wiki




Post new topic Reply to topic  [ 4 posts ] 
Author Message
 Post subject: CSQ
PostPosted: Mon Jun 29, 2009 9:23 pm 
Offline

Joined: Sun Feb 15, 2009 9:45 am
Posts: 91
This may sound Dumb but what is CSQ :!:


Top
 Profile  
 
 Post subject: Re: CSQ
PostPosted: Mon Jun 29, 2009 9:32 pm 
Offline
User avatar

Joined: Fri Feb 20, 2004 11:18 am
Posts: 1389
Location: Not Biloxi
Carrier SQulech. No PL, DPL or Data required to open the rx'er. Just carrier

_________________
I generate Board Warnings


Top
 Profile  
 
 Post subject: Re: CSQ
PostPosted: Mon Jun 29, 2009 9:33 pm 
Offline
Mr. Bad Example
User avatar

Joined: Sat Feb 21, 2004 10:11 am
Posts: 8097
Location: Nancy's Bedroom... ooh aah
--------------------------------------------------------------------------------

It's a carrier with nothing "riding" on it like a tone.

A simple carrier squelch or noise squelch operates strictly on the signal strength of the signal, such as when a television mutes the audio or blanks the video on "empty" channels, or when a walkie talkie mutes the audio when no signal is present. In some designs, the squelch threshold is preset. For example, television squelch settings are usually preset. Receivers in base stations at remote mountain top sites are usually not adjustable remotely from the control point.
In devices such as radiotelephones (also known as two-way radios), the squelch threshold is set with an adjustable knob marked squelch. This setting adjusts the threshold at which signals will open the audio channel. Backing off the control will turn on the audio, and the operator will hear white noise if there is no signal present. The usual operation is to adjust the control until the channel just shuts off - then only a small threshold signal is needed to turn on the speaker. However, if a weak signal is annoying, the operator can adjust the squelch to open only when stronger signals are received.
A typical FM two-way radio carrier squelch circuit takes out the voice components of the receive audio by passing the detected audio through a high-pass filter. A typical filter might pass frequencies over 4,000 Hz (4 kHz). The squelch control adjusts the gain of an amplifier which varies the level of noise coming out of the filter. The audio output of the filter and amplifier is rectified and produces a DC voltage when noise is present. The presence of noise creates a DC voltage which turns the receiver audio off. When a signal with little or no noise is received, the voltage goes away and the receiver audio is unmuted. Some applications have the receiver tied to other equipment that uses the audio muting control voltage as a "signal present" indication.

_________________
President-in-Exile, Seattle Area Radio Communications And Scanner Traffic Intercept Crew (SARCASTIC)
Don't feel bad if you can't use your STD100/200; there are still people using Digital Frequency Search!
Bunnery definition for the under-fives


Top
 Profile  
 
 Post subject: Re: CSQ
PostPosted: Tue Jun 30, 2009 9:30 am 
Offline

Joined: Sun Feb 15, 2009 9:45 am
Posts: 91
Thanks for the info ( Can't Believe all these Yrs I didn't Know that ) :beer:


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 8 hours


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by electricity. Copyright © 2013 Interceptradio.com